General Physical Examination

Step 1/2

Body Weight
Determine the body weight. Foreseeable changes due to growth should be taken into account.

Step 2/2

Body Height
Determine the body height. Foreseeable changes due to growth should be taken into account.

Step 1/9

Pitch
Determine pitch x of the shoe (difference between heel height A and sole thickness B in the ball area). Measure A and B and apply the formula x = A - B. Transfer the determined pitch to the h-Cast.

Step 2/9

If the patient wishes to use different shoe models, take all measurements. If the shoes only differ in heel height A and sole thickness B, but have the same pitch x, note the maximum values of A and B and continue with step 4. Otherwise go to step 3.

Step 3/9

If the shoe models have a different pitch x, there are two options:

1. The orthosis is equipped with a system joint that can be adjusted to different pitches. This is the case with the NEURO HiSWING system ankle joint.
2. The patient chooses a set pitch.

Option 1: determine the maximum and minimum value of pitch x of the different shoe models. Calculate the mean value. This value is needed for making the negative cast. For all other work steps, use the maximum value of pitch x.

Step 4/9

Height Compensation
The patient is standing on the h-Cast. Check if the patient is plumb, e.g. by using a laser plumb bob. The plumb bob should fall from the 7th cervical vertebrae (C7) through the cleft between the buttocks and the middle of the supportive area of both feet. If this is not the case – e.g. due to a unilateral contracture – the patient requires a height compensation. Determine the height compensation (see C at step 1) and transfer it to the h-Cast. Check the result.

Step 5/9

Shoe Size
Determine the shoe size (S1). If the feet differ in length, write down the larger shoe size.

Step 6/9

Individual Normal Posture
Check the individual normal posture in the sagittal plane with the help of a laser plumb bob. The plumb bob should fall as follows

• from the body’s centre of gravity
• across the greater trochanter
• centrally through the ap measurement at knee height
• to the rear third of the front half of the supportive area.

With extension deficits, the knee joint does not serve as a reliable point of orientation. If this is the case, approximate the above-mentioned fixed points as closely as possible.
Note: take the length difference of the feet into account, if present.

Step 7/9

Length Difference
Determine the length difference L. Measure S1 and S2 and apply the formula L = S1 - S2. Write down the length difference L in order to be able to compensate the difference during the following steps.
Important! For a symmetrical stride length, there should be equal leverage ratios on both sides. To achieve that, the rolling-off line’s position and the heel lever must be adjusted in case of a functional shortening (e.g. due to a height compensation). 

Step 8/9

Range of Motion in the Upper Ankle Joint in Dorsiflexion
The range of motion in the upper ankle joint is measured based on the individual normal posture. Position the patient on the h-Cast, taking into account the leg length/height compensation and the shoe pitch. Measure the range of motion of the upper ankle joint in dorsiflexion based on the individual normal posture.

Step 9/9

Range of Motion in the Upper Ankle Joint in Plantar Flexion
The range of motion in the upper ankle joint is measured based on the individual normal posture. Position the patient on the h-Cast, taking into account the leg length/height compensation and the shoe pitch. Measure the range of motion of the upper ankle joint in plantar flexion based on the individual normal posture.

Step 1/6

Deformities
The patient is standing on the h-Cast. Check whether the leg axis deviates from the neutral position.

Step 2/6

Varus Deformity
If there is a deviation in varus, correct it as much as possible and determine the value of the corrected varus deformity. If the deformity cannot be corrected, we recommend that you still use the box on the General Orthotic Treatment Sheet to document the determined value. Then, determine the maximum varus deformity without load on the leg. If the values match, there is a deformity, but no instability.

Step 3/6

Valgus Deformity
If there is a deviation in valgus, correct it as much as possible and determine the value of the corrected valgus deformity. If the deformity cannot be corrected, we recommend that you still use the box on the General Orthotic Treatment Sheet to document the determined value. Then, determine the maximum valgus deformity without load on the leg. If the values match, there is a deformity, but no instability.

Step 4/6

Hyperextension
Measure the maximum knee hyperextension. Correct it, if possible, to achieve a physiological knee angle. Due to patient-specific conditions, this may not be attainable in some cases. In any case, determine the corrected hyperextension (e.g. 4°). All values, which exceed 0° flexion (e.g. 4° flexion), undo any hyperextension and are marked as 0°.

Step 5/6

Extension Limitation of the Hip
Apply the Thomas test to determine the extension limitation of the hip. The patient is lying on their back. Place one hand under the lumbar vertebrae to check the delordosing of the lumbar spine. Bring the leg not to be tested into hip flexion with the knee bent. The hip flexion angle is measured on the side to be tested. Please note that the determined extension limitation of the hip can affect the individual normal posture in the sagittal plane.

Step 6/6

Extension Limitation of the Knee
The patient is standing on the h-Cast. Adjust it so that all influencing factors, such as the extension limitation of the hip, are taken into account. Measure the knee angle. It deviates from the physiological angle if there is an extension limitation of the knee and/or hip. Pain can also lead to a deviation.

Step 1/10

Step 2/10

Dorsiflexion – Muscle Strength 5 and 4
The patient is lying on their stomach. The foot of the leg to be tested is hanging over the edge of the examination table. Hold the lower leg in place with one hand without restricting the muscle function. Press against the back of the foot with the other hand. Have the patient bring the foot into dorsiflexion. At complete range of motion against gravity with full resistance, the muscle strength is 5. At range of motion against gravity with some resistance, the muscle strength is 4.

Step 3/10

Dorsiflexion – Muscle Strength 3
The patient is seated. The lower legs are hanging over the edge of the examination table. Hold the lower leg in place with one hand without restricting the muscle function. Have the patient bring the foot into dorsiflexion. At range of motion against gravity, the muscle strength is 3.

Step 4/10

Dorsiflexion – Muscle Strength 2
The patient is lying on the side of the leg to be tested. Place one hand under the foot so that it is no longer resting on the examination table. Have the patient bring the foot into dorsiflexion. At range of motion with gravity eliminated, the muscle strength is 2.

Step 5/10

Dorsiflexion – Muscle Strength 1 and 0
The patient is lying on the side of the leg to be tested. Place one hand under the foot so that it is no longer resting on the examination table. Have the patient bring the foot into dorsiflexion. Palpate if there is any muscle activity. At slight contraction with no joint motion, the muscle strength is 1. At no evidence of contraction, there is a total paralysis and the muscle strength is 0.

Step 6/10

Step 7/10

Plantar Flexion – Muscle Strength 5 and 4
The patient is lying on their stomach. The foot of the leg to be tested is hanging over the edge of the examination table. Hold the lower leg in place with one hand without restricting the muscle function. Press against the forefoot from below with the other hand. Have the patient bring the foot into plantar flexion. At complete range of motion against gravity with full resistance, the muscle strength is 5. At range of motion against gravity with some resistance, the muscle strength is 4.

Step 8/10

Plantar Flexion – Muscle Strength 3
The patient is lying on their stomach. The leg to be tested is flexed. Have the patient bring the foot into plantar flexion. At range of motion against gravity, the muscle strength is 3.

Step 9/10

Plantar Flexion – Muscle Strength 2
The patient is lying on the side of the leg to be tested. Place one hand under the foot so that it is no longer resting on the examination table. Have the patient bring the foot into plantar flexion. At range of motion with gravity eliminated, the muscle strength is 2.

Step 10/10

Plantar Flexion – Muscle Strength 1 and 0
The patient is lying on the side of the leg to be tested. Place one hand under the foot so that it is no longer resting on the examination table. Have the patient bring the foot into plantar flexion. Palpate if there is any muscle activity. At slight contraction with no joint motion, the muscle strength is 1. At no evidence of contraction, there is a total paralysis and the muscle strength is 0.

Step 1/10

Step 2/10

Knee Extension – Muscle Strength 5 and 4
The patient is seated. The lower legs are hanging over the edge of the examination table. Hold the thigh in place with one hand without restricting the muscle function. Press against the lower leg above the foot with the other hand. Have the patient bring the knee into extension. At complete range of motion against gravity with full resistance, the muscle strength is 5. At range of motion against gravity with some resistance, the muscle strength is 4.

Step 3/10

Knee Extension – Muscle Strength 3
The patient is seated. The lower legs are hanging over the edge of the examination table. Hold the thigh in place with one hand without restricting the muscle function. Have the patient bring the knee into extension. At range of motion against gravity, the muscle strength is 3.

Step 4/10

Knee Extension – Muscle Strength 2
The patient is lying on the side of the leg not to be tested. Support and lift the upper leg with one hand. Hold the pelvis in place with the other hand without restricting the muscle function. The leg to be tested is slightly flexed. Have the patient bring the knee into extension. At range of motion with gravity eliminated, the muscle strength is 2.

Step 5/10

Knee Extension – Muscle Strength 1 and 0
The patient is lying on their back. The leg to be tested is slightly flexed in hip and knee. The other leg is extended. Have the patient bring the knee into extension. Palpate if there is any muscle activity. At slight contraction with no joint motion, the muscle strength is 1. At no evidence of contraction, there is a total paralysis and the muscle strength is 0.

Step 6/10

Step 7/10

Knee Flexion – Muscle Strength 5 and 4
The patient is lying on their stomach. The foot of the leg not to be tested is hanging over the edge of the examination table and the leg to be tested is flexed. Hold the thigh in place with one hand without restricting the muscle function. Press against the lower leg close to the foot with the other hand. Have the patient bring the knee into flexion. At complete range of motion against gravity with full resistance, the muscle strength is 5. At range of motion against gravity with some resistance, the muscle strength is 4.

Step 8/10

Knee Flexion – Muscle Strength 3
The patient is lying on their stomach. The foot of the leg not to be tested is hanging over the edge of the examination table and the leg to be tested is flexed. Hold the thigh in place with one hand without restricting the muscle function. Have the patient bring the knee into flexion. At range of motion against gravity, the muscle strength is 3.

Step 9/10

Knee Flexion – Muscle Strength 2
The patient is lying on the side of the leg not to be tested. The upper leg is slightly flexed. Support and lift the upper leg with one hand. Hold the pelvis in place with the other hand without restricting the muscle function. Have the patient bring the knee into flexion. At range of motion with gravity eliminated, the muscle strength is 2.

Step 10/10

Knee Flexion – Muscle Strength 1 and 0
The patient is lying on their stomach. The foot of the leg not to be tested is hanging over the edge of the examination table and the leg to be tested is slightly flexed. Support the flexed leg with one hand. Have the patient bring the knee into flexion. With the other hand, palpate if there is any muscle activity. At slight contraction with no joint motion, the muscle strength is 1. At no evidence of contraction, there is a total paralysis and the muscle strength is 0.

Step 1/10

Step 2/10

Hip Flexion – Muscle Strength 5 and 4
The patient is lying on their back. The lower legs are hanging over the edge of the examination table. Hold the pelvis in place with one hand without restricting the muscle function. Push against the thigh close to the knee with the other hand. Have the patient bring the hip into flexion. At complete range of motion against gravity with full resistance, the muscle strength is 5. At range of motion against gravity with some resistance, the muscle strength is 4.

Step 3/10

Hip Flexion – Muscle Strength 3
The patient is lying on their back. The lower legs are hanging over the edge of the examination table. Hold the pelvis in place with one hand without restricting the muscle function. Have the patient bring the hip into flexion. At range of motion against gravity, the muscle strength is 3.

Step 4/10

Hip Flexion – Muscle Strength 2
The patient is lying on the side of the leg not to be tested. The upper leg is slightly flexed in hip and knee. Support and lift the upper leg with one hand. Hold the pelvis in place with the other hand without restricting the muscle function. Have the patient bring the hip into flexion. At range of motion with gravity eliminated, the muscle strength is 2.

Step 5/10

Hip Flexion – Muscle Strength 1 and 0
The patient is lying on their back. Hip and knee of the leg to be tested are slightly flexed. Support the flexed knee with one hand. Have the patient bring the hip into flexion. With the other hand, palpate if there is any muscle activity. At slight contraction with no joint motion, the muscle strength is 1. At no evidence of contraction, there is a total paralysis and the muscle strength is 0.

Step 6/10

Step 7/10

Hip Extension – Muscle Strength 5 and 4
The patient is lying on their stomach. The feet are hanging over the edge of the examination table. Press against the thigh close to the knee with one hand. Have the patient bring the hip into extension. Make sure that the pelvis stays on the examination table. At complete range of motion against gravity with full resistance, the muscle strength is 5. At range of motion against gravity with some resistance, the muscle strength is 4.

Step 8/10

Hip Extension – Muscle Strength 3
The patient is lying on their stomach. The feet are hanging over the edge of the examination table. Have the patient bring the hip into extension. Make sure that the pelvis stays on the examination table. At range of motion against gravity, the muscle strength is 3.

Step 9/10

Hip Extension – Muscle Strength 2
The patient is lying on the side of the leg not to be tested. The upper leg is slightly flexed. Support and lift the upper leg with one hand. Hold the pelvis in place with the other hand without restricting the muscle function. Have the patient bring the hip into extension. At range of motion with gravity eliminated, the muscle strength is 2.

Step 10/10

Hip Extension – Muscle Strength 1 and 0
The patient is lying on their stomach. Have the patient bring the hip into extension. Palpate if there is any muscle activity. At slight contraction with no joint motion, the muscle strength is 1. At no evidence of contraction, there is a total paralysis and the muscle strength is 0.

Step 1/5

Activity
Assess the activity level together with your patient while taking into consideration foreseeable changes.

Step 2/5

1. Indoor Walker
The patient has the ability or the potential to make transfers and to move with an orthosis on even surfaces at low walking speed. Ambulation is possible for a very short distance and duration due to the physical condition of the patient.

Step 3/5

2. Restricted Outdoor Walker
The patient has the ability or the potential to move with an orthosis at low walking speed and is able to overcome small environmental obstacles such as curbs, single steps or uneven surfaces.

Step 4/5

3. Unrestricted Outdoor Walker
The patient has the ability or the potential to move at medium to high and also varying speed and to overcome most environmental obstacles. Additionally, the patient can walk on open terrain and perform professional, therapeutic and other activities, which do not apply an above average mechanical load on the orthosis.

Step 5/5

4. Unrestricted Outdoor Walker with Especially High Demands
The patient has the ability or the potential to move with an orthosis like the unrestricted outdoor walker. Additionally, the increased functional demands can generate high impact loads, tension and/or deformation on the orthosis. These patients are mainly athletes and children.

Step 1/1

ap Measurement
Determine the ap measurement by using a calliper. Measure at the slightly flexed, relaxed knee. Measure at a right angle from the knee fold to the longitudinal axis of the lower leg and parallel to the movement direction.
Note: in order to avoid measuring errors, do not use the patella as a basis for determining the ap measurement, as the patella’s position can vary (e.g. in case of luxations, TEPs and patella alta).